RARE user and assistance email list

[mc36 <>]

hi,
in general, bundles are created over physical interfaces and not 
subinterfaces...
so you have to bundle the sdns togeher, then configure the subinterface on 
top of the bundle interface...
much like this: http://sources.freertr.org/cfg/p4lang-rout018.tst
here you create a vlan 11 subinterface on top of sdn3 and sdn4...
br,
cs



On 10/24/22 12:11, Xavier Jeannin wrote:
> Hello Csaba,
>
> Thank   you for your email.
> I want to collect our user traffic and put their traffic in a dedicated VLAN 
> (then established the BGP peering between the RENATER bacbone PE and the 
> client) - see picture below.
>
> My understanding (I am certainly   wrong) is that I have to put the interface 
> (sdnXX) in the bundle (not the sub interface) and it should be enough (see 
> configuration attached).
> But it does not work
> I try also to put the sub-interface but no success.
>
> Could you advice what type of configuration should I use for this use case?
>
> The example available on http://docs.freertr.org/guides/reference/ are
>
> conn-bundle01              bundle of ethernet port
> conn-bundle02              bundle of serial port
> conn-bundle03              bundle of ethernet ports
> conn-bundle04              bundle of serial ports
> conn-bundle05              bundle over bridge
> conn-bundle06              bridge over bundle
> conn-bundle07              replicating bundle
> conn-bundle08              unreplicating bundle
> conn-bundle09              dejittering bundle
> conn-bundle10              loadbalancing bundle
> conn-bundle11              multichassis bundle
> conn-bundle12              backup bundle
>
> Thank you
> Regards
> Xavier
>
> Le 20/10/2022    10:03, mc36 a   crit  :
> > hi,
> > lacp is there:
> > you have to configure it per member interface with both the lacp knob and the 
> > bundle-group knob...
> > the first one is just the protocol sender and you can omit if you do "mode 
> > on" on the remote side...
> > so that latter is the interesting part in the fastpath, and it's heavily 
> > tested with the dataplanes...
> > br,
> > cs
> >
> > On 10/20/22 09:58,  wrote:
> > > Hello
> > >
> > > I allow myself to post again this request about LACP supporting trunk as if 
> > > this would not be implemented, it will impact strongly our use case 
> > > deployment.
> > >
> > > Thank you
> > > Regards
> > > Xavier
> > >
> > > Le 17/10/2022       18:23, Xavier Jeannin a     crit   :
> > > > Hello
> > > >
> > > > I am still stuck with the creation of LACP handling a trunk.
> > > > In the meantime, I review my configuration and see that "bridge-group 2" was 
> > > > not declared in P4 server after correction same pb.
> > > > This really something that block this work.
> > > >
> > > > Any suggestion ?
> > > >
> > > > Regards
> > > > Xavier
> > > >
> > > > Le 27/09/2022       10:37, Xavier Jeannin a     crit   :
> > > > > Hello
> > > > >
> > > > > I create a testbed on which (see picture attached):
> > > > >
> > > > >    * the client is connected on a WEDGE (L2-PPN) at Layer 2 using Ethernet    
> > > > >  or VLAN
> > > > >    * The WEDGE (L2PPN) should be connected to our backbone thanks to a bond 
> > > > > of interfaces (LACP). The traffic on the LACP must be a VLAN trunk.
> > > > >
> > > > > I see a strange behaviour and it is certainly due to how I configure it.
> > > > >
> > > > > If I put the 2     vlans (11-12) on the all interfaces taking part on the 
> > > > > LACP, it does not work.
> > > > > If     I put the 1 vlan only on each interface of the taking part on the 
> > > > > LACP, it     works. But in this case the traffic should not be well shared 
> > > > > between the LACP links.
> > > > >
> > > > > I suspect I implement this use case not appropriately (see configuration 
> > > > > attached + picture). Any suggestion?
> > > > >
> > > > > Regards
> > > > > Xavier
> > > > >
> > > > >
> > > > >
> > > > > --
> > > > > Xavier JEANNIN
> > > > > Network Dpt.
> > > > > GN4-3 Network technology evolution (WP6 T1) task leader
> > > > > T   l. : +33 1 5394 2042
> > > > > Mob. : +33 6 3017 0963
> > > > > www.renater.fr
> > > > --
> > > > Xavier JEANNIN
> > > > Network Dpt.
> > > > GN4-3 Network technology evolution (WP6 T1) task leader
> > > > T   l. : +33 1 5394 2042
> > > > Mob. : +33 6 3017 0963
> > > > www.renater.fr
> > >
> > > --
> > > Xavier JEANNIN
> > > Network Dpt.
> > > GN4-3 Network technology evolution (WP6 T1) task leader
> > > T   l. : +33 1 5394 2042
> > > Mob. : +33 6 3017 0963
> > > www.renater.fr
> > >
> > > _._,_._,_
> > > ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
> > > Groups.io Links:
> > >
> > > You receive all messages sent to this group.
> > >
> > > View/Reply Online (#768) <https://groups.io/g/freertr/message/768> | Reply To Group 
> > > <> | Reply To Sender 
> > > <> | Mute This Topic 
> > > <https://groups.io/mt/93945667/6006518> | New Topic <https://groups.io/g/freertr/post>
> > > Your Subscription <https://groups.io/g/freertr/editsub/6006518> | Contact Group Owner 
> > > <> | Unsubscribe <https://groups.io/g/freertr/unsub> 
> > > []
> > >
> > > _._,_._,_
> > From - Fri Oct 21 08:43:28 2022
> > X-Mozilla-Status: 0001
> > X-Mozilla-Status2: 00000000
> > Return-Path: <>
> > Received: from zmtain01.partage.renater.fr (LHLO
> > zmtain01.partage.renater.fr) (194.254.240.20) by
> > zstore-b1-018.partage.renater.fr with LMTP; Fri, 21 Oct 2022 06:02:16
>
> --
> Xavier JEANNIN
> Network Dpt.
> GN4-3 Network technology evolution (WP6 T1) task leader
> T  l. : +33 1 5394 2042
> Mob. : +33 6 3017 0963
> www.renater.fr