The mailing list for users of the eduroam Configuration Assistant Tool (CAT)

[Tomasz Wolniewicz <twoln AT umk.pl>]

We dropped the eduroam® name for the profile since people were complaining. Now if you run an installer it is supposed to install the eduroam profile and delete the previous eduroam@ if it finds one.

Can you run the installer form the command line with -DEBUG=4 ? the produced CAT.log should have the details.

Tomasz

W dniu 12.09.2024 o 15:11, Smith, Anthony [asmith2] pisze:

The one in the original picture was a policy installed eduroam. I have tried on unmanaged PCs and only the one profile is installed , in the past the Eduroam profile from the website was called Eduroam® .

 

Anthony

 

From: Tomasz Wolniewicz <twoln AT umk.pl>
Sent: Thursday, September 12, 2024 1:46 PM
To: Smith, Anthony [asmith2] <Anthony.Smith2 AT liverpool.ac.uk>; 'cat-users AT lists.geant.org' <cat-users AT lists.geant.org>
Subject: Re: [[cat-users]] Catool issue

 

Hi,

CAT installers always install a profile named "eduroam" with SSID "eduroam" and on network cards supporting HotSpot 2.0 it also installs a profile called "eduroam via partner" with SSID "cat-passpoint-profile".

If you call "netsh wlan show profiles" then you should see them.

This second profile is added so that the device can be ready for a special use case, which is not jet much used - still it is better to give uses all possible chances of connecting.. Some service providers have agreed to accept eduroam users but not by broadcasting eduroam SSID. Instead they use HotSpot 2.0 on whatever SSID they like and announce the RoamingConsortium identifier - 001bc50460, which is reserved for eduroam.

If a Windows device is in the range of such a network, Windows network selection will probably show something like "the_actual_ssid, eduroam via partner" - this changes with Windows versions and I am not sure what is the actual message. Your device should connect to such a network automatically. The SSID does not matter in such a case, but it cannot be empty in the config, therefore we just set it to "cat-passpoint-profile".

If you are in the range of an SSID eduroam and also such HS 2.0 network, the SSID is supposed to take precedence.

So I think that all is fine with the installer and the standard eduroam connection should work without any problems.

Yours

Tomasz Wolniewicz

 

W dniu 12.09.2024 o 11:55, "Smith, Anthony [asmith2]" (via cat-users Mailing List) pisze:

Issue seems to be the SSID is incorrect and Hotspot2 added. Tried with no hotspot config , didnt work. changes SSID but left hotspot2 and didnt work. Only works when no hotspot 2 config and the correct SSID

 

 

below is what comes form the website

 

  <SSIDConfig>
<SSID>
<hex>6361742D70617373706F696E742D70726F66696C65</hex>
<name>cat-passpoint-profile</name>
</SSID>
</SSIDConfig>

<Hotspot2>
<DomainName>liverpool.ac.uk</DomainName>
<RoamingConsortium>
<OUI>001bc50460</OUI>
</RoamingConsortium>
</Hotspot2>

 

 

 

Below is what is should be

 

  <SSIDConfig>
<SSID>
<hex>656475726F616D</hex>
<name>eduroam</name>
</SSID>
</SSIDConfig>

 

 

 

From: Smith, Anthony [asmith2]
Sent: Thursday, September 12, 2024 10:20 AM
To: 'cat-users AT lists.geant.org' <cat-users AT lists.geant.org>
Subject: Catool issue

 

 

Have you had any reports that when using Catool on a windows device , it installs and shows as a managed network but does not show as an available network to connect to?

 

Regards

 

Anthony Smith

Network Analyst

Network Services Team

IT Services

 

 Start a Teams Chat with Anthony Smith

 

University of Liverpool I IT Services I Brownlow Hill I Liverpool I L69 3GG

Mob: 07741238375

Tel: 01517958411

 

To unsubscribe, send this message: mailto:sympa AT lists.geant.org?subject=unsubscribe%20cat-users
Or use the following link: https://lists.geant.org/sympa/sigrequest/cat-users

--
Tomasz Wolniewicz
      
    
-- 
Tomasz Wolniewicz

Attachment: smime.p7s
Description: Kryptograficzna sygnatura S/MIME